Sun–Thu, 09:00–17:00 Egypt
[email protected] +20 127 265 8400 EN / العربية — in preparation

Security Systems

CCTV, access control, structured cabling and the networks everything else depends on — designed so the cabling outlives the equipment plugged into it, and so the doors behave correctly when the fire alarm operates.

Overview

Security and low current systems are usually bought as a list of devices, which is why they so often disappoint. A camera count says nothing about whether a face will be identifiable, a door controller says nothing about whether the door releases in a fire, and neither says anything about the cabling that both depend on and that will still be in the building long after the equipment has been replaced.

Milagre engineers, supplies, installs, tests, commissions and maintains CCTV, access control, structured cabling, fibre and data networks, telephone, SMATV and parking control systems. Because we also deliver the fire systems in the same buildings, the interfaces between them are designed rather than discovered on site.

Plain definition

Low current — also called extra-low voltage, or ELV — is the regional term for the building systems that run on low voltage rather than mains power: CCTV, access control, data and telephone networks, television distribution, public address, and the structured cabling underneath all of them. They are grouped into one package because they share containment, share equipment rooms, and above all share cabling. That cabling normally outlasts two or three generations of the equipment connected to it, which is why it deserves considerably more design attention than it usually receives.

System types we work with

The table below sets out the low current systems within scope. Where the scope column reads on enquiry, the stages we take on depend on the project rather than being fixed.

SystemTypical applicationMilagre scope
CCTV & video surveillance Perimeters, entrances, production floors, public areas, car parks Design · Supply · Install · Test · Commission · Maintain
Access control Door controllers, readers, turnstiles, credential management Design · Supply · Install · Test · Commission · Maintain
Structured cabling Copper horizontal cabling, patching, containment and labelling Design · Supply · Install · Test · Commission · Maintain
Fibre backbone Riser and inter-building links beyond copper distance limits Design · Supply · Install · Test · Commission · Maintain
Data networks Switching, PoE distribution and segmentation for building systems Design · Supply · Install · Test · Commission · Maintain
Telephone systems Extension distribution and handsets across a site Design · Supply · Install · Test · Commission · Maintain
SMATV & TV distribution Hotels, hospitals and residential blocks Design · Supply · Install · Test · Commission · Maintain
Parking & barrier control Gates, barriers, ticketing and vehicle access Design · Supply · Install · Test · Commission · Maintain
Intruder detection Perimeter and internal alarm, monitored or local On enquiry
Intercom & video entry Gatehouses, residential entrances, reception points On enquiry
Public address & background music Non-life-safety announcement and music distribution — voice evacuation is covered under fire alarm On enquiry

Applications

What the systems have to do changes completely with the building and who uses it. These are the environments we work in most often, and what each one demands.

Industrial & manufacturing sites
Long perimeters, vehicle gates and weighbridges, and cameras that have to survive dust, vibration and heat. Coverage is usually driven by material movement and incident evidence rather than by intrusion alone.
Education & campuses
Multiple buildings watched from one control room, and a credential population that turns over completely every few years — which makes administration, not hardware, the part that has to be designed well.
Hotels & resorts
A hard boundary between public, guest and back-of-house areas, staff access tiers that follow shift patterns, and camera positions constrained by the fact that guests must never feel watched.
Retail & malls
Tenant boundaries that shift with every fit-out, car park and vehicle access management, and footage that has to be good enough to be used in an insurance or liability claim.
Offices & commercial buildings
Turnstiles and visitor management at reception, lift and floor access tied to tenancy, and a cabling infrastructure that will be re-patched every time a tenant moves.
Warehouses & logistics
Loading bays and dock doors where most stock loss occurs, aisles with poor light, and coverage that must remain useful when racking is reconfigured.

Why an engineered approach matters

Two installations with identical equipment schedules can produce completely different results — one where the footage identifies a person and the doors release correctly in an alarm, and one where the footage is unusable and nobody has ever tested the interface.

  • Every camera view has a stated purpose. Detect, observe, recognise or identify — decided per position and delivered by pixel density across the target, not by pointing a high-resolution camera in a general direction and hoping.
  • Storage calculated before the recorder is bought. Retention period, camera count and bitrate produce a real number. Storage that quietly runs short overwrites the footage somebody will eventually need.
  • Cabling designed to outlive the equipment. Distance limits respected, copper and fibre chosen deliberately, PoE budgets calculated, every link certified and labelled — so the next upgrade is a device swap rather than a rebuild.
  • The fire alarm interface designed, not improvised. Doors on escape routes release on a hardwired signal that does not depend on the access control server being alive. This is a life-safety function that falls between two contractors on most projects.
  • Networks segmented sensibly. Cameras and controllers are numerous, physically reachable and rarely updated. They belong behind controlled routing rather than flat on the business network.

Our process

The sequence is the same for one building and for a campus. The scale changes; the order does not.

01 · Site survey
Engineers record building fabric and cable routes, equipment room and cabinet space, existing containment and infrastructure worth retaining, lighting levels, and the operational boundaries that access control will have to follow.
02 · Coverage & credential design
Camera positions with a stated purpose for each view, and a door schedule setting out which doors are controlled, which are monitored, and which are on escape routes.
03 · Storage & bandwidth calculation
Retention period, camera count, resolution and bitrate turned into an actual storage figure and an actual network load, before any recorder or switch is specified.
04 · Containment & cabling design
Cable routes, distance limits, copper against fibre decisions, PoE budgets and cabinet layouts — the part of the installation that will still be in place after the equipment has been replaced twice.
05 · Shop drawings
Camera and door layouts, containment routes, rack elevations, port and patch schedules issued for approval.
06 · Supply & installation
Equipment procured to the approved make and model, cabling installed and labelled to the approved drawings.
07 · Testing & certification
Copper and fibre certified to the cabling standard with results issued per link, and every camera checked for focus, field of view and low-light performance against what the design said it would achieve.
08 · Commissioning
Access levels and schedules programmed, recording and retention verified, and the fire alarm interface proven by operating the fire alarm and watching the doors release.
09 · Handover & training
As-built drawings, cable test certificates, port schedules, credential administration training and O&M manuals for the people who will run it daily.
10 · Maintenance
Scheduled checks of recording, retention, camera condition and door hardware, and re-testing of the fire alarm release interface.

Standards & approvals

Security and cabling work is governed by standards in the same way fire systems are, and the door release interface is governed by the fire code rather than by anything in this discipline. The standards below are the ones that normally apply; confirmation of which Milagre formally designs to is pending.

StandardWhat it governs
TIA-568 Structured cabling — horizontal and backbone design, distance limits, testing and certification
ISO/IEC 11801 Information technology cabling — the international counterpart
IEC 62676 Video surveillance systems for security applications — including the pixel density levels that define what a camera can actually deliver
IEC 60839 Alarm and electronic security systems, including access control
NFPA 72 & Egyptian Fire Code The fire alarm interface — release of doors on escape routes, and the monitoring of that interface
Civil Defence Local authority approval and inspection
Certifications

Milagre holds documented manufacturer authorisations from Velocity, Zeta and Hikvision; the letters are on file and available on request. No quality-management certification and no contractor classification is held, and neither is claimed — what we do not claim sets that out in full. Nothing will be claimed here without a certificate to support it.

Frequently asked questions

What does "low current" actually mean?

It is the regional term — extra-low voltage, or ELV, elsewhere — for the building systems that run on low voltage rather than mains: CCTV, access control, data and telephone networks, TV distribution, public address, and the structured cabling underneath all of them.

They are grouped as one package for practical reasons. They share containment, they share equipment rooms and cabinets, and they share cabling. Treating them as one coordinated scope is what stops four contractors each installing their own containment through the same ceiling void.

How many cameras do I need, and at what resolution?

Camera count comes from what each view has to achieve, not from floor area. IEC 62676-4 sets out four operational levels by pixel density across the target: approximately 25 pixels per metre to detect that someone is present, 62.5 to observe what they are doing, 125 to recognise somebody already known, and 250 to identify a stranger from the footage alone.

One camera can meet different levels at different distances, so the design work is deciding what each position has to deliver. An entrance where faces must stand up as evidence needs a much tighter view than a yard where movement only has to be seen.

Specifying everything at identification level wastes storage and money. Specifying everything at detection level produces footage that shows an incident happened and nothing more — which is the complaint we are most often called in to fix.

How long should footage be kept, and how much storage is that?

Retention is set by your operational or legal requirement rather than by the equipment, and thirty days is a common baseline. The storage then follows arithmetically: a 4 MP camera recording continuously at around 4 Mbit/s produces roughly 40 GB a day, so thirty days is a little over 1 TB — for that one camera.

Modern codecs and recording only on motion or analytic events cut this substantially, often by more than half. The point is that the calculation should be done from your actual camera count, bitrate and retention period before the recorder is specified, rather than discovered a month after handover when the system starts overwriting.

What happens to access-controlled doors when the fire alarm goes off?

Doors on escape routes must release so people can get out. That is a life-safety requirement under the fire code, not an access control setting, and it is normally achieved with fail-safe locking devices that unlock when power is removed — released by a hardwired signal from the fire alarm system, with manual break-glass units on the escape side.

The critical point, and the one most often missed, is that the release must not depend on the access control software, its server or its network being healthy. The interface is hardwired for the same reason a fire alarm circuit is monitored. A door that unlocks only when a Windows service is running is not a fire-safe door.

Doors not on escape routes may be fail-secure and stay locked. Which doors fall into which category comes from the escape strategy and the authority having jurisdiction — and it should be written into a door schedule at design stage, not decided by whoever installs the lock.

Can I reuse my existing coaxial cabling if I move to IP cameras?

Sometimes, using ethernet-over-coax adapters, and it can be genuinely worthwhile where recabling would mean opening finished ceilings throughout an occupied building.

The compromises are real, though: less bandwidth and shorter distances than dedicated twisted pair, more limited power delivery, and harder fault-finding, because installed coax is almost always undocumented and of unknown quality. Where the cable routes are accessible, new structured cabling is usually the better decision — it will outlive the cameras you are buying today.

Do the security systems need their own separate network?

They need separation, but not necessarily separate physical infrastructure. Video surveillance produces sustained high bandwidth that will affect everything else on a flat network, and cameras and door controllers are themselves an exposure — numerous, physically accessible, and running firmware that in practice is rarely updated.

The usual answer is a dedicated VLAN on shared switching with controlled routing between it and the business network. A physically separate network is used where the security requirement justifies paying for a second infrastructure.

Related projects

Milagre has delivered security and low current systems across industrial plant, university campuses, hotels, resorts and shopping malls. All thirteen are named on the projects page, three of them shown in full.

Two different problems. Two different inboxes.

A new installation and a system that has stopped working are not the same urgency, so they do not go to the same place.

New project

Request a quote

An engineer attends site, establishes what each camera view actually has to achieve and who needs to go where, and you receive a scope tied to camera positions and a door schedule rather than a device count.

Existing system

Service & maintenance

Cameras that stopped recording without anyone noticing, a controller nobody can program, storage filling faster than it should, or cabling installed by a contractor who has since disappeared.

Would rather fill in a form? Use the enquiry form

Sunday–Thursday, 09:00–17:00 (Egypt). We do not operate a 24-hour line, and we would rather say so than imply a response we cannot commit to. Outside working hours, message us on WhatsApp and it will be picked up the next working morning.