Fire Suppression Systems
Special hazard systems for rooms where water would destroy what you are trying to protect — sized by concentration calculation, and only ever as good as the enclosure that holds the agent in.
Overview
Suppression systems exist for the rooms where the fire is not the only thing that can destroy the contents. A sprinkler protects the building; in a server room, an archive or a switchroom it also guarantees the loss of exactly what the system was installed to save. Gaseous suppression extinguishes without leaving anything behind.
Milagre engineers, supplies, installs, tests, commissions and maintains FM-200, Novec 1230 and CO₂ systems. The design work is a calculation, not a selection from a catalogue: the agent quantity comes from the measured volume of the enclosure, and the enclosure is verified rather than assumed.
The design concentration is the percentage of agent, by volume, that must be present in the room to extinguish the fire — the extinguishing concentration for that fuel, plus a safety margin. It is calculated against the room's actual volume at its lowest expected temperature, and it determines how much agent you buy and how many cylinders stand in the corner. It is also why a room altered after commissioning may no longer be protected: enlarge the volume, and the same cylinders now deliver a lower concentration than the one the system was signed off at.
System types we work with
The table below sets out the suppression technologies within scope. Where the scope column reads on enquiry, the stages we take on depend on the project rather than being fixed.
| System | Typical application | Milagre scope |
|---|---|---|
| FM-200 (HFC-227ea) | Server rooms, switchrooms, control rooms — small cylinder footprint | Design · Supply · Install · Test · Commission · Maintain |
| Novec 1230 (FK-5-1-12) | The same spaces, where a low global warming potential is required | Design · Supply · Install · Test · Commission · Maintain |
| CO₂ — high and low pressure | Normally unoccupied enclosures: generators, paint booths, machinery | Design · Supply · Install · Test · Commission · Maintain |
| Inert gas (IG-541, IG-55, argon) | Large volumes, and where a naturally occurring agent is preferred | On enquiry |
| Kitchen hood wet chemical | Commercial cooking lines, extract hoods and ducts | On enquiry |
| Foam systems | Flammable liquid storage, fuel handling, loading racks | On enquiry |
| Water mist | Machinery spaces and heritage interiors, where water volume must be minimised | On enquiry |
| Condensed aerosol | Small sealed enclosures and electrical cabinets | On enquiry |
Applications
Suppression is specified per room, not per building. These are the spaces we are asked to protect most often, and what makes each one particular.
- Server rooms & data halls
- Where the equipment is worth more than the building and water is the second disaster. Almost always paired with very early warning detection, so the agent is released while there is still only a smouldering cable.
- Electrical switchrooms & substations
- High-value plant, no occupancy to speak of, and a fire that will keep re-igniting while the fault is live. Agent hold time matters more here than anywhere else.
- Generator & machinery enclosures
- Hot surfaces, fuel and forced ventilation in a space nobody normally occupies — the classic case for CO₂, and the classic case for getting the ventilation shutdown interlock right.
- Archives, libraries & collections
- Contents that cannot be replaced and cannot be dried out. The requirement is not only to extinguish but to leave no residue behind.
- Commercial kitchens
- Cooking oil fires that water spreads rather than extinguishes, requiring a wet chemical system on the appliance line and in the extract duct, interlocked to shut off the gas supply.
- Flammable liquid stores & paint booths
- Fast-developing fires in confined, ventilated spaces where the extinguishing agent has to arrive before the ventilation carries the fire somewhere else.
Why an engineered approach matters
Suppression systems are frequently compared on the price of the agent and the number of cylinders. Neither tells you whether the system will work, because a correctly calculated system in a leaking room will not hold concentration long enough to put the fire out, and no quantity of agent fixes that.
- The agent chosen for the room, not the invoice. Occupancy, volume and available cylinder space decide the agent. Fitting the cheapest agent per kilogram into a room it does not suit is how CO₂ ends up somewhere people work.
- Concentration calculated from a measured enclosure. Room volume taken on site rather than from a drawing that predates the raised floor, the ceiling void and the last fit-out.
- Enclosure integrity tested, not assumed. A door fan test before handover, so a leaking room is found while the trades who can seal it are still on site.
- Pressure relief sized properly. A discharge into a sealed room raises pressure fast. Under-sized venting is how a system designed to save a room damages it instead.
- Safety interlocks proven at commissioning. Pre-discharge alarm, time delay, abort and lockout, ventilation shutdown and damper closure — demonstrated end to end, because these are the functions that decide whether a discharge is survivable.
Our process
The sequence is the same for a single switchroom and for a data hall with a dozen protected volumes. The scale changes; the order does not.
- 01 · Hazard analysis
- What is in the room, what would burn, whether people are normally present, and what the consequence of losing the room actually is.
- 02 · Agent selection
- Matched to occupancy, volume, available cylinder storage and any environmental or client policy constraint — not to the cheapest agent per kilogram.
- 03 · Concentration & quantity calculation
- Design concentration for the specific fuel, applied to the measured volume of the enclosure at its lowest expected temperature, giving the agent mass and cylinder count.
- 04 · Pipe network, nozzle layout & shop drawings
- Flow calculations for the pipe network so every nozzle delivers its share within the required discharge time, with nozzle positions coordinated against racks and obstructions.
- 05 · Enclosure review & pressure relief
- Identifying what has to be sealed, and sizing the pressure relief venting — a discharge into a sealed room raises pressure sharply, and under-sized venting damages the room it is protecting.
- 06 · Supply & installation
- Cylinders, pipework, nozzles, detection and control equipment procured to the approved make and model and installed to the approved drawings.
- 07 · Room integrity test
- A door fan test measuring enclosure leakage and predicting the hold time, before commissioning rather than after — a failed enclosure is a construction problem, and it is cheapest to find while trades are still on site.
- 08 · Commissioning
- Full cause and effect proven: detection coincidence, pre-discharge alarm, time delay, abort and lockout functions, ventilation and damper shutdown, and the interface to the fire alarm system.
- 09 · Handover & training
- As-built drawings, concentration and flow calculations, the room integrity certificate, O&M manuals, and training for the people who will be in the building when it operates.
- 10 · Maintenance
- Six-monthly agent quantity and pressure checks, annual functional testing of detection and interlocks, and re-verification of enclosure integrity whenever the room is altered.
Standards & approvals
Suppression design is governed by code, not preference, and the safety provisions in particular are not optional. The standards below are the ones that normally apply to this work; confirmation of which Milagre formally designs to is pending.
| Standard | What it governs |
|---|---|
| NFPA 2001 | Clean Agent Fire Extinguishing Systems — design concentration, hold time, safety of occupied spaces, inspection intervals |
| NFPA 12 | Carbon Dioxide Extinguishing Systems — including the time delay, alarm and lockout requirements that make CO₂ survivable |
| ISO 14520 | Gaseous fire-extinguishing systems — the international counterpart series |
| NFPA 17A & 96 | Wet chemical systems and commercial cooking operations — kitchen hood suppression |
| Egyptian Fire Code | National requirements — كود الحماية من الحريق |
| Civil Defence | Local authority approval and inspection |
Milagre holds documented manufacturer authorisations from Velocity, Zeta and Hikvision; the letters are on file and available on request. No quality-management certification and no contractor classification is held, and neither is claimed — what we do not claim sets that out in full. Nothing will be claimed here without a certificate to support it.
Frequently asked questions
FM-200, Novec 1230, inert gas or CO₂ — which one do I need?
Three things decide it: whether the room is normally occupied, how big it is, and how much space you have for cylinders.
FM-200 (HFC-227ea) and Novec 1230 (FK-5-1-12) are halocarbon clean agents used at design concentrations that permit occupancy, and both store as liquid under pressure, so the cylinder footprint is small. That combination is why they dominate server rooms and switchrooms. Novec 1230 has a very low global warming potential, which increasingly decides between the two where regulation or a client's own policy applies.
Inert gas systems using argon and nitrogen are also suitable for occupied spaces, but the agent is stored as a compressed gas and needs substantially more cylinders for the same volume. They suit large protected volumes where the storage space exists.
CO₂ is in a different category and is covered separately below.
Is it safe to be in the room when the system discharges?
For clean agents, yes, within the design margins — halocarbon and inert gas systems in occupied spaces are designed to reach a concentration that extinguishes the fire while remaining safe for the time it takes to leave, and that margin is part of the calculation rather than an afterthought.
For CO₂, no, and this is the most important thing on this page. CO₂ extinguishes by displacing oxygen to a level that will not sustain combustion, which is also a level that will not sustain a person. It is used only in normally unoccupied enclosures, and it is required to have pre-discharge alarms, a time delay long enough to leave, and lockout arrangements for anyone working inside.
Those safeguards are only real if they were commissioned and are still being tested. A CO₂ system with an interlock nobody has exercised since handover is the scenario the standards exist to prevent.
What is a room integrity test and why does it matter?
Reaching the design concentration is not enough. The agent has to stay at concentration long enough to fully extinguish the fire and prevent re-ignition — commonly a ten-minute hold — and that depends entirely on how well the room retains it.
A room integrity test, normally a calibrated door fan test, measures the enclosure's leakage and predicts the hold time without discharging any agent. Failures almost always come from the same places: unsealed cable penetrations, door undercuts, raised floor voids and gaps above ceilings.
It is worth repeating after alterations. A room that passed at handover will not still pass once somebody has cut three new cable routes through the wall and not resealed them.
Will the agent damage my servers?
No. Clean agents are electrically non-conductive and leave no residue — that is the entire reason they are used instead of water. Equipment running before a discharge is normally running after it.
The real risks in a discharge come from elsewhere: the pressure excursion in a tightly sealed room if the relief venting was under-sized, and the acoustic energy from high-pressure nozzles, which can affect hard disk drives when nozzles are positioned close to open racks. Both are design considerations, and both are avoidable.
What happens after a discharge — can the system be refilled?
Yes. Cylinders are refilled or exchanged, actuation devices reset, and the system returned to service. The question that matters is how long that takes, because the room is unprotected until it is finished, and it is usually a room that cannot simply be shut down. Ask any contractor where cylinders are refilled and what the turnaround is, before you appoint them rather than after a discharge.
A discharge should also be investigated, not just reset. An unexplained one nearly always points to a detection or interlock problem that will happen again.
How often does a suppression system need servicing?
Under NFPA 2001, agent quantity and container pressure are checked at least every six months, with cylinders weighed or level-checked and any showing significant loss removed and refilled. Detection, actuation, alarms and interlocks are functionally tested annually, and cylinders are hydrostatically tested on the interval set by the applicable pressure vessel rules.
Enclosure integrity should be re-checked whenever the room changes, which is an event rather than a date — and it is the check most often missed, because nothing about the system itself looks any different.
Related projects
Milagre has delivered suppression works across industrial plant, university campuses, hotels, resorts and shopping malls. All thirteen are named on the projects page, three of them shown in full.
Two different problems. Two different inboxes.
A new installation and a system that has stopped working are not the same urgency, so they do not go to the same place.
Request a quote
An engineer attends site and measures the enclosure rather than estimating it, so you receive a scope tied to a concentration calculation and a realistic view of what the room will need sealed.
Service & maintenance
A cylinder that has lost pressure, a system that has discharged and needs returning to service, a room altered since commissioning, or a service that is overdue.
Would rather fill in a form? Use the enquiry form